 |
 |
 |
|
The XL-size m!ka Microphone Arm is the perfect choice for everyone who has to deal with long distances between a microphone's mounting position and the speaker positions. As a long-distance solution, the arm bridges distances up to 107.5cm. Thus, the m!ka Microphone Arm XL is a good choice to equip even large tables and setups with microphones.
By adjusting only a few knurled screws you can make sure Yellowtec’s m!ka Microphone Arm securely fastens your mic according to its weight, in any position you pull it to.
Be it a switch in seats or a recording setup which is used by different persons, our m!ka Mic Arm allows you to customize your mic’s position within seconds. Fully compatible with the whole m!ka system, you can take full advantage of the given variety of mounting options to tailor your setup to your individual needs.
- Microphone Arm XL has a maximum reach of 42.3" (107.5cm)
- Supports microphones weighing up to 3.31 lbs (1.5kg)
- Adjustable friction joints
- Wiring concealed by tubes and joints
- Open-end cable tails (without XLR's)
- Option to add Neutrik Gold XLR connectors
- Sturdy tube construction
- Made of durable, silk-mat anodized aluminum
- Various mounting options (see below)
STEP 1 | INTERNAL CABLE TERMINATION OPTIONS
Yellowtec m!ka Microphone Arms have an internal cable concealed in the tubes and joints of the arm. By default, this cable comes unteriminated from the factory. This is because in broadcast environments, it is customary to feed a loose cable end through a small hole or conduit before connecting it to a preamp or a recording device. Since the cable with a connector installed may not fit through a small hole or conduit, the default option is for the cable ends to be unterminated.
However, Pro Audio LA can terminate your Yellowtec m!ka Microphone Arm with Neutrik Gold connectors so it's ready to "plug and play." Alternatively, if you'd like to terminate the cable yourself but would like us to include the Neutrik Gold XLR connectors, that option is also available.
STEP 2 | OPTION TO ADD A MICROPHONE
Various microphones are available to bundle with your Yellowtec m!ka Microphone Arm. Choose from a range of products at a range of price points
STEP 3 | EXTENSION TUBE OPTION
While it is not required, the Shure A26X 3" Extension Tube makes mounting some microphones like the Shure SM7B easier due to the position of the XLR position on the SM7B microphone. The A26X extention tube can also help with mounting clearence/length with other microphones.
STEP 4 | OPTIONAL CLOUD CL-1 CLOUDLIFTER
The
Cloud CL-1 Cloudlifter gives dynamic microphones up to +25dB of additional active output. This translating to more signal, less noise, and a stronger presence in the audio signal. It is a highly-recommended accessory that will improve the sound quality of almost any dynamic microphone. Phantom power (48 volts) supplied by your preamp provides the power to the Cloudlifter which then "activates" your microphone for higher, cleaner output.
OPTIONAL ADDITIONAL MOGAMI 2549 XLR CABLE
The internal cable of the Yellowtec m!ka Microphone Arm has 3 feet of Slack on the output side at the bottom of the arm to connect to any microphone preamp, recording device, or the Cloud CL-1 Cloudlifter. If using the CL-1 Cloudlifter, an additional XLR cable is required to connect from the CL-1 to your microphone preamp or recording device. Easily add whatever length you need using this option if you don't already have an XLR cable to make this connection.
STEP 5 | MOUNTING OPTIONS
Mounting Option 1 | Non-Permanent Table Clamp Mounting Option
- Use Yellowtec Table Clamp (Model YT3210)
- Suitable table thickness: 0.71 - 2.88 inches (18 - 74mm)
- NOT compatible with round table edges
- No drilling required
Mounting Option 2 | Permanent, Elevated Mounting (3.5" Higher than Table Top)
- Use Yellowtec Table Through Mount (Model YT3215)
- Suitable table thickness: up to 0.98 inches (25mm)
- Requires drilling a hole through the desk
Mounting Option 3 | Permanent, Elevated Mounting (3.5" Higher than Table Top)
- Use Yellowtec Table Mount (Model YT3216)
- Suitable for any table thickness
- 3 screws secure Table Mount to table top
- No drilling required
Mounting Option 4 | Permanent Mounting (Flush to Table Top)
- Use Yellowtec Bushing Mount (Model YT3211)
- Suitable table thickness: up to 1.77 inches (45mm)
- Requires drilling a hole through the desk
For more information on this or any other Yellowtec product, visit www.yellowtec.com.
Mounting options for m!ka Microphone Arms
Installation instructions for m!ka Microphone Arms
How to choose the right m!ka Microphone Arm
|
|
|
 |
|
 |
|